Payment with: Money Order, Cashier's Check, Personal Check,
PayPal? Contact Seller.
Offering this new "Made-in-the-USA" Peerless Gear LTH 2000-006A modular hydrostatic transaxle at a 21% discount off the $611.70 MSRP from Peerless Gear -- almost 1/4 off. This transaxle is factory-lubricated, ready to bolt-in and run.
This new-in-box hydrostatic transaxle is manufactured to fit Sears, Craftsman, Poulan, Husqvarna, and Weed-Eater brand front-engine lawn tractors and riding mowers. It has a 4-3/4"-diameter input pulley mounted over the 7-1/4"-diameter cooling fan, with the pulley centerline 4-1/2" above the case-seam centerline. The speed-control lever is on the left side; the brake and free-wheeling controls are on the right side. It has 3/4"-diameter axle shafts that extend out from the case 4-3/4" on each side; the axles have 3/16" x 2-3/4" keyways with snap-ring grooves on the axle ends. The overall end-to-end axle length is approximately 29-1/4". The case has two sets of industry-standard mounting holes -- the close-together holes are on 13" side-to-side centers x 1-3/4" front-to-back centers; the far-apart mount holes are on 16-1/4" x 2-1/2" centers.
1. The holes on the lower-front corners of the transaxle are not threaded, since the mower manufacturer uses 5/16"-18 self-threading bolts to hold the front support(s) to these corners. If you are re-using your original bolts or equivalent OEM bolts, make sure they have clean threads when re-installing these supports. If you do not have the original-style bolts and are using standard machine-thread bolts for these front-corner supports, you will need to carefully tap these holes to match the threads of your bolts. WARNING: If you plan on pre-tapping these holes, the case material is only about 0.060" (1/16") thick at the back of these holes, so measure the hole depth and set your tap accordingly, or you will break through the case into the gear-lube area.
2. Make sure you have the front support securely fastened to the transaxle or misalignment will occur.
DRIVE-LINKAGE NOTE: These transaxles are shipped from the factory with the F-N-R lever locked in Neutral by the Nylock nut which is tightened against the painted-dot spring on the right side of the transaxle. When installing the transaxle into the mower, align the shift lever in the Neutral position on the fender, then connect the shift linkage to the transaxle, adjusting as necessary. When linkage Neutral matches transaxle Neutral and the linkage is installed, loosen the F-N-R Lever nut one (1) turn.
Being new, this transaxle is covered by the Peerless 2-year Consumer Use/90-day Commercial Use/30-day Rental Use Limited Warranty within the USA and the 1-year Consumer/90-day Commercial/30-day Rental Limited Warranty outside the USA. A dated receipt will be provided to validate the warranty, dated to reflect its arrival at your place so you won't lose warranty coverage for travel time. Note that the warranty covers defects in material and workmanship -- it is not a blanket guarantee against abuse and mistreatment. A copy of the Peerless Warranty will also be included with the transaxle.
This is an 'A'-Input transaxle -- it mounts in the mower with the input pulley, shift arm and brake AHEAD OF the axle. DO NOT ATTEMPT TO USE THIS TRANSAXLE on any rider where the transaxle is mounted with the input pulley, brake and shift arm BEHIND the axle, as it is not engineered for this mode of operation.
QUESTIONS? Please -- if you are attempting to use this transaxle to replace a different transaxle -- before you ask a "Will-it-fit?" question, compare the measurements of your transaxle to the dimensions I have listed above for this transaxle, and note the Model and Serial Numbers off your current transaxle. Yes, that may require safely jacking up your mower, removing a wheel, then crawling under the mower with a scale, tape measure, flashlight and notepad, as well as a rag to carefully clean off dirt and grease. In your question, also include the Model and Serial Number off the mower. Thanks!
Also, if you cannot find the 2000-xxx Number on your transaxle but the hydro module has a 6892P91 on its label, this is a 2000-006A. It should also have an H6891P92 label on the axle module.
No sales tax if sold outside Missouri. Sales tax of 5.225% must be charged to a Missouri Buyer.
SHIPPING NOTE: This transaxle will be shipped with a plug in place of the breather valve on top of the overflow reservoir, and the breather valve is in a separate plastic bag. This prevents fluid loss if the carton is turned over during shipping. Before installing the transaxle in your mower, remove the plug with a 3/16" Allen wrench, then install the breather valve with a7/16" nut driver or socket. Do not overtighten the breather valve.
SHIPPING: Buyer pays shipping on my Items from Postal Code 64730 USA. I can ship these Items worldwide. Within the USA, Item will be shipped UPS Ground Insured unless the buyer specifies otherwise. Item will be shipped promptly after receiving proper payment. If the eCrater Shipping Wizard costs appear to be high in your Checkout, please read our Store's "Terms" before being scared off by the Shipping Wizard's freight costs, and use the "Ask Seller a Question" link, if necessary.
And please make sure the eCrater Home Page Heading displays the Stars-&-Stripes with the "U.S." notation in the upper-right corner so prices will be displayed in U.S. Dollars, not Australian Dollars or British Pounds.
PAYMENT Options --
PAYPAL -- Contact Seller.
PREFERRED: We prefer a money order, bank draft or certified check payment sent via Postal Mail. We can also accept a business or personal check, but these require a 4-7 day clear period...except...we consider a check drawn on a Credit Union to be the same as a certified check.
INTERNATIONAL: Contact Seller for international payment options.
FEEDBACK: Our Feedback is 100%, which is good. The latest Feedback, however, is in December of 2011, which may raise questions. The reason for this is because we had to drop PayPal as an Approved Payment Method in our Store due to eCrater’s restrictions, and the only way Feedback can be left is if we show PayPal as an Approved Payment Method and the Buyer pays with PayPal through the eCrater Checkout. For this reason, there are no Feedbacks since December of 2011, even though we’ve had hundreds of satisfied customers since then. If you would like to get a referral from a recent customer near you, please let us know. We have nothing to hide, and your satisfaction is our priority.
Our philosophy..."No matter how many material possessions or awards you may acquire in your lifetime, the only thing you will ever truly own is your reputation."
Other Products from roms-peerless-transaxle-supply: